ChipWerke Piggyback Tuning Module for

Audi A6 C7

2011-2014, 3.0 TFSI (CGWD,CGXB,CTUA)

Stock 310 HP

Stage 1 +55 HP

Stage 2 up to 35% HP

Power and torque increases may vary. Figures depend on many variables, such as fuel quality, altitude, and vehicle condition. Fuel economy highly depends on driving habits.

$349.99

$449.99

SAVE 22%

ChipWerke piggyback tuning module is the best plug-and-play performance upgrade for the Audi A6 3.0T. It intercepts both intake manifold pressure sensors and recalibrates the stock sensor readings for an extra 55 HP with Stage 1. Up to a 35% increase is possible with custom Stage 2 tune and supporting mods. ChipWerke uses OEM connectors, so no wire cutting or drilling is needed. It is completely untraceable and does not affect engine health in the long run. ChipWerke improves power output throughout the whole RPM range and delivers better performance without compromising OEM drivability or causing any diagnostic flags.

WHY CHOOSE CHIPWERKE PIGGYBACK MODULE

Significant Power Gains

ChipWerke increases power output by 55 HP with Stage 1. It delivers faster acceleration and better power delivery throughout the whole RPM band.

Stage 2 Tune for Supporting Mods

Contact us for custom Stage 2 tune. With bolt-on upgrades like intake kit, supercharger pulleys, and higher octane fuel, gains of up to 35% over stock are possible.

Completely Untraceable

ChipWerke does not make changes to the stock ECU. It leaves no traces or diagnostic flags including the Audi/VAG TD1 code when removed.

Wirelessly Adjust Your Tune

Fine-tune the performance with seven preset levels and optimize the power increase on the fly through the free mobile app.

Better Fuel Economy

Improves low-end torque so the engine maintains speed with less effort, resulting in up to 15% better fuel economy.

Plug-and-Play Installation

Simple DIY installation in under 15 minutes. It requires no special tools, wire cutting or splicing, or permanent modifications.

Does Not Overwrite Stock ECU

Factory ECU remains unaltered, meaning you get a hassle-free performance upgrade while OEM safety measures continue to function as normal.

Extensive Customer Support

ChipWerke comes with two years of manufacturer’s warranty and extensive USA-based after-sales support for total peace of mind.

HOW DOES CHIPWERKE PIGGYBACK MODULE WORK

The ChipWerke piggyback tuning module is the best alternative to a permanent ECU tune. It connects to the factory wiring harness to alter the readings from the MAP/IAT sensors of the 3.0-liter supercharged engine. ChipWerke intercepts and optimizes the stock signals to modify boost pressure, increasing horsepower and torque.

ChipWerke works within factory parameters and does not permanently alter the stock ECU, so it boosts power output while retaining OEM daily driveability and reliability. The ChipWerke’s tune can be adjusted with seven preset levels (-3 to +3) easily via the mobile app to optimize the power increase for your driving style, varying fuel quality, or altitude changes.

EASY PLUG-AND-PLAY INSTALL

The ChipWerke piggyback tuning module connects to the Audi A6 3.0T’s MAP/IAT sensors at each side of the 3.0 TFSI engine. It intercepts the factory wiring harness with OEM-quality plugs, so no wire splicing, cutting, drilling, or permanent modifications are required. The guide included in the package shows specific installation instructions for your vehicle.

The basic things to consider in all applications are as follows:

Turn off the engine and wait for it to cool down. Leave the driver’s door open for 15 minutes while keeping the keyfob at least 35 feet away from the car to ensure the ECU shuts down completely.
Locate where you want to mount the module. Make sure that it is away from the areas that tend to heat up relatively more.
Make sure the ChipWerke harness is not overly stretched and is protected against water.
Make sure that plugs are securely connected in place and that there are no unused plugs left.

View Installation Guide